If you are in the process of starting a jewel line, there is a need to know how they are created so that you meet customer demands more effectively. Several methods are involved in making the final products. As long as the methods adhere to unique products are created, and this is what will bring customers to your shop. Below are steps involved in Tufa casting custom jewelry NM.
Pieces of stone where the design will be made are prepared before other process kicks off. The size of the stones to be used is determined by the choice and type of models the designer ought to create. After the right size have been cut, the next thing is to smoothen all of them and make them flat. The aim of flattening them is to make them identical and perfect to each other.
On the size of the stone that has already been created carefully design a sketch of what you need to make. These sketches should be done in such a way that there are no errors at all. And to achieve all this, take time when drawing your outline.
Use the necessary design tools to carve the stone. There are a couple of tools that one can use in this process such as sewing needles, chisel tools, and wood files. This carving has to be correctly done because once some parts of the stone are cast away, they cannot be reused again. Space which has been created will be used to fill silver fillings to form the piece. Air holes must be left so that when the silver is being poured the process can be achieved very first.
Before silver is poured in the intended space, stones have to be carbonized to get rid of oxygen. The pieces of stones are attached using clamps and rubbers, and this makes the process as perfect as possible. Solid silver is then put in a crucible, and high temperatures of heat are introduced to melt it into an exceptional liquid form. When silver is in its liquid form state, it is then poured on spaces that were left.
Sand is used to smoothening and clean the model. Sand cleans and removes the unwanted parts, and the good news is that the texture is not affected at all. Also, citric acid pickling solution is used in cleaning the surfaces. The pickling solution is effective in removing any traces of fire that are gotten when the soldering process is taking process.
Then polishing is done on the model that has been cleaned using sand. Polishing is aimed at making the design look even more refreshing and attractive. Water can be used, or rubber or even other recommended polishing compounds. The compound range from abrasive to non abrasive, and for every stage of polishing different compounds are used.
When everything is done according to plans, the manufacturer had it is time to call it a day. At this stage, everything has been achieved, and the owner has a chance to make the designs appear how they want. The final product can now be prepared to meet the specifics of a particular market. Sand cleaning and polishing take most a lot of time compared to other processes.
Pieces of stone where the design will be made are prepared before other process kicks off. The size of the stones to be used is determined by the choice and type of models the designer ought to create. After the right size have been cut, the next thing is to smoothen all of them and make them flat. The aim of flattening them is to make them identical and perfect to each other.
On the size of the stone that has already been created carefully design a sketch of what you need to make. These sketches should be done in such a way that there are no errors at all. And to achieve all this, take time when drawing your outline.
Use the necessary design tools to carve the stone. There are a couple of tools that one can use in this process such as sewing needles, chisel tools, and wood files. This carving has to be correctly done because once some parts of the stone are cast away, they cannot be reused again. Space which has been created will be used to fill silver fillings to form the piece. Air holes must be left so that when the silver is being poured the process can be achieved very first.
Before silver is poured in the intended space, stones have to be carbonized to get rid of oxygen. The pieces of stones are attached using clamps and rubbers, and this makes the process as perfect as possible. Solid silver is then put in a crucible, and high temperatures of heat are introduced to melt it into an exceptional liquid form. When silver is in its liquid form state, it is then poured on spaces that were left.
Sand is used to smoothening and clean the model. Sand cleans and removes the unwanted parts, and the good news is that the texture is not affected at all. Also, citric acid pickling solution is used in cleaning the surfaces. The pickling solution is effective in removing any traces of fire that are gotten when the soldering process is taking process.
Then polishing is done on the model that has been cleaned using sand. Polishing is aimed at making the design look even more refreshing and attractive. Water can be used, or rubber or even other recommended polishing compounds. The compound range from abrasive to non abrasive, and for every stage of polishing different compounds are used.
When everything is done according to plans, the manufacturer had it is time to call it a day. At this stage, everything has been achieved, and the owner has a chance to make the designs appear how they want. The final product can now be prepared to meet the specifics of a particular market. Sand cleaning and polishing take most a lot of time compared to other processes.
About the Author:
Get a summary of the things to keep in mind when choosing a tufa casting custom jewelry NM designer and more information about an experienced designer at http://www.bojoejewelry.com now.
No comments:
Post a Comment